Call Today

 

Almost everyone will have their own way of thinking in relation to A Step-by-Step Guide to Installing a Bathtub.

Mounting a bath tub isn't specifically brain surgery, yet it does call for solid plumbing, woodworking, as well as in some cases, tiling skills. Replacing an old tub with a brand-new one is likewise a moderately challenging project. If the old bathtub is easily obtainable, the job can move rapidly; if you need to open up a wall surface to get rid of the old tub as well as position the new bath tub, the job is a lot harder. In either case, the project is within a home handyman's skills, although you will certainly require an assistant to vacate the old bathtub as well as set in the new one. Make sure you have actually certified on your own for the job and fit attempting it. Rather than hiring a contractor to take control of a halfway-completed job, it is better to take into consideration utilizing one before you start. Chances are you might need an expert plumber to make tube connections.
This post will certainly assist you mount a new tub in your restroom if you have actually currently acquired a new bathtub and do not require to alter the arrangement of your previous water supply pipes.
Your tools and also material list ought to consist of the following:

 

• New Tub


• Hammer


• Pipeline Wrenches


• Prybar


• Safety Glasses


• Degree


• Pliers


• Flexible Wrench


• Putty Blade


• Screwdriver


• Cold Knife


• Tape Measure


• Pipe Caps


 

Removing Old Taps

If you require to change old faucets with new ones as a part of your setup, then the first thing you should do is separate the water supply. After doing so, activate the faucets to drain any kind of water continuing to be in the system. The process of getting rid of the existing faucets can be quite bothersome due to the limited access that is frequently the instance.
Use a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipes to the faucets. Have a towel ready for the staying water that will certainly come from the pipes. When the supply pipelines have actually been gotten rid of, utilize the very same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly need to stop the single faucets from turning throughout this process. When the taps have actually been removed, the holes in the bath/basin will certainly have to be cleansed of any old sealing compound.
Prior to moving on to fit the brand-new faucets, compare the pipe links on the old faucets to the new faucets. If the old faucets are longer than the new faucets, then a shank adapter is required for the brand-new taps to fit.

 

 

Suitable New Taps

If the tails of the brand-new taps are plastic, then you will certainly need a plastic port to prevent damages to the thread. One end of the adapter fits on the plastic tail of the tap and also the other end gives a link to the existing supply pipes.
If you require to fit a monobloc, then you will call for minimizing couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next off, place the tap in the placing hole in the bath/basin making certain that the washers remain in area in between the faucet as well as the sink. Safeguard the tap in position with the producer given backnut. Once the faucet is firmly in place, the supply pipes can be linked to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with typical faucet adapters. The former type ought to be linked to the tap finishes initially, tightening up just by hand. The supply pipelines can later on be linked to the various other end. Tighten both ends with a spanner after both ends have been linked.

 

 

Setting up the Bathtub

Using the two wood boards under its feet, position the tub in the needed position. The wooden boards are useful in evenly spreading out the weight of the tub over the area of the boards as opposed to concentrating all the weight onto four tiny points.
The following goal is to make sure that the bathtub is leveled all round. This can be achieved by inspecting the level and changing the feet on the bath tub until the level reviews degree.
To install taps, fit the bottom of the outermost adaptable faucet port to the ideal supply pipe by making a compression sign up with; then do the exact same for the various other faucet.
Switch on the water and inspect all joints as well as brand-new pipework for leakages and tighten them if required. Fill up the tub as well as additionally examine the overflow electrical outlet and also the normal outlet for leaks.
Ultimately, repair the bathroom paneling as described in the manufacturer's instruction manual. Tiling as well as sealing around the bath tub should wait till the tub has been used at the very least when as this will certainly settle it right into its final position.

 

 

Preparing for the Installation

To start with, the supporting structure provided with the bathroom needs to be fitted (if called for) according to the supplier's directions. Next off, fit the taps or mixer to the tub. When fitting the faucet block, it is very important to ensure that if the tap comes with a plastic washer, it is fitted in between the bathroom and the taps. On a plastic bath, it is additionally practical to fit a sustaining plate under the faucets unit to avoid pressure on the bathtub.
Fit the versatile faucet adapters to the bottom of both faucets making use of 2 nuts and also olives (in some cases supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet with the hole in the bath. Make use of the nut provided by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Ensure you use all of the provided washers.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Attach all-time low of the overflow tube in a comparable manner.The bath should currently be ready to be fitted in its final placement.

 

 

Tiling Around the Bathtub

In the area where the bathroom fulfills the floor tile, it is needed to seal the joins with a silicone rubber caulking. This is essential as the fitting can move sufficient to split a rigid seal, triggering the water to permeate the wall between the bath as well as the tiling, leading to difficulties with dampness and also feasible leaks to the ceiling listed below.
You can pick from a variety of coloured sealants to assimilate your components and also fittings. They are offered in tubes as well as cartridges, and also can sealing voids up to a width of 3mm (1/8 inch). If you have a bigger void to load, you can load it with spins of soaked newspaper or soft rope. Keep in mind to always fill the bath tub with water prior to sealing, to allow for the activity experienced when the tub remains in usage. The sealant can crack rather early if you do not take into account this movement before securing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are likewise easily readily available on the marketplace. It is a good idea to fit the tiles utilizing waterproof or water resistant adhesive and cement.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

I found that blog post about How to Install a Bathtub while doing a lookup on the internet. Are you aware of another person who is truly interested in the subject? Feel free to share it. We take joy in reading our article about How to Install a Bathtub Yourself.

The right fix? Ring!